Black Hawk Labs 4U + 2U Standard MiniRaQ Especificaciones descargar pdf

MiniRaQ Installation Overview

(TM*)

Congratulations on your purchase of the MiniRaQ vertical rack system. The MiniRaQ

is available in 4U, 6U and 8U sizes based on size and usage restrictions for a variety of

applications. The is designed from heavy gauge steel and finished to last a lifetime.

It is designed to hold up to 400 pounds when properly installed for your most demanding

needs such as extended runtime battery back up systems, low profile power distribution

transformers, POE equipment and many other rack mountable products.

The MiniRaQ System can be mounted on a variety of vertical substrates including

wooden framing studs 16” on center, solid or block concrete walls, and approved

plywood electrical panel or directly onto existing 2 Post racking. Please see detailed

instructions on the following pages.

Mounting hardware is provided for installing into solid wall studs and #12-24

screws for mounting on 2 Post rack. The can even be mounted in a 2 Post rack

Back-to-Back configuration if clearances allow, which may increase U space utilization

in some instances.

(TM) (TM)

(TM)

MiniRaQ

For installing the MiniRaQ System into any other surface not specifically

mentioned in this manual, please consult local building code requirements

to insure safe and secure installation.

(TM)

www.miniraq.com

PAGE 1

All Trademarks are the property of their respective owners. *Patents pending.

Warning

Back-plate of is designed with

3 mounting options:

“A” hole pattern (10)

“B” Slots are centered at 16 inches

for #10 by 2” screws (10) into studs

or other solid wood surface.

“C” hole pattern (10)

apparatus

allows mounting

in standard 2 post open frame rack.

accommodates

toggle bolts for mounting on block wall

or NEC electrical panel grade plywood.

Built in level allows easy installation

for single service personnel

Top access for data

or power cabling

The apparatus allows attachment

for 1U or 2U patch panel directly

inside the back-panel without

sacrificing any space in the mounting

surface of the side panels.

Earth Grounding Stud

integrated further

assisting quick and

convenient system install

Ancillary equipment, both rack

and non-rack mountable, can be

attached to the side of the

back-panel by hanging or screwing

onto the back-panel.

Lances are incorporated into the

MiniRaQ to allow data and

power cable management for

input and output wiring using

either top or bottom egress,

as well as to facilitate service loops.

(TM)

Large rear panel access allows

pass though cable routing in

2 Post Back-to-Back

mounting applications

FIGURE 1

1 2 3 4 5 6 7 8 9 10

Indice de contenidos

Pagina 1 - MiniRaQ Installation Overview

MiniRaQ Installation Overview(TM*)Congratulations on your purchase of the MiniRaQ vertical rack system. The MiniRaQis available in 4U, 6U and 8U sizes

Pagina 2 - FIGURE 2

www.miniraq.comPAGE 10BHL WILL IN NO WAY BE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL,CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE,SERVICE

Pagina 3 - 2-Post Mounting option

www.miniraq.comPAGE 2MiniRaQ Installation Instructions(TM)DetailedFirst confirm that the main back panel of the MiniRaQ will be mounted onto arecommen

Pagina 4 - Mounting option

www.miniraq.comPAGE 32 Post Rack mounting option (Hole Pattern A)Using supplied #12-24 screws align andinsert 1 screw. Do not fully tight screw buteng

Pagina 5 - FIGURE 5

www.miniraq.comPAGE 4Begin installing suppliedscrews in pilot holes at thetop then drill and installremaining screws in thepattern. 10 screwsrecommend

Pagina 6 - Caution:

www.miniraq.comPAGE 5An approved hollow wall application is considered to be either of the following;Cinder Block wall or NEC type 3/4” plywood electr

Pagina 7 - Bracket Arm

www.miniraq.comPAGE 6Mounting to Concrete Wall with TAPCON® bolts(Hole Pattern C)Place the MiniRaQ main back panel against the wall in the preferred l

Pagina 8

www.miniraq.comPAGE 7With the MiniRaQ main back panel mMiniRaQ main back panel accommodates all bracketssizes available, 4U, 6U and 8U versions.Proper

Pagina 9

www.miniraq.comPAGE 8MiniRaQ Specifications(TM)Item MeasurementHeight: 19.25 in (489 mm)Width: 19.00 in (483 mm)Depth:4U version: 9.50 in (241 mm)6U v

Pagina 10

www.miniraq.comPAGE 9BlackHawk Labs, LLC Limited Factory WarrantyTerms of WarrantyNon-transferable WarrantyExclusionsThe limited warranty provided by

Comentarios a estos manuales

Sin comentarios

Black Hawk Labs 4U + 2U Standard MiniRaQ Especificaciones

Busca en linea o descarga Especificaciones para Bastidores Black Hawk Labs 4U + 2U Standard MiniRaQ. Black Hawk Labs 4U + 2U Standard MiniRaQ [no] Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Bastidores Black Hawk Labs 4U + 2U Standard MiniRaQ